|
|
Evil
Eye Model The Evil Eye is a wide, tremendously functional
board for less than high energy surf. With our proprietary engineered, Casuarina Pine
Deck Membrane (CPDM) for flex management, this model will allow you to put the Evil Eye in places not normally achievable
with other boards. It is an excellent substitute for the funshape or longboard and it easily fits in your
quiver and your car. The low entry rocker, single concave bottom, with FCS Fusion quad setup and wide diamond
tail will give the board drive and spontaneity. Ride it 6” – 8” shorter than your normal
short board. With all the waves you will be catching and fun you’ll be having, “Evil Eyes”
will be glaring at you!!! Two Constructions – Two Different Glides. Polyester – with dual wood stringers is for a more soulful ride, slightly heavier than our
EPX II, for those that like the polyester feel. It skates and slides through sections with ease and handles
the sloppy chop like a warm knife cutting butter. EPX II - our epoxy
version, with Dual High Density Polyurethane Stringers (DHDPS), is light for high performance surfing, punting, and all around
ripping. EVIL EYE 5.4, 5.8, 6.0, 6.4 - 21 ½ to 23, 2 ½ to 3
|
|
Motu
Flyer Model Motu Flyer is the great all around
Thumbtail for many great wave categories, hollow beachbreaks and reefs, long points, and all quality surf in between.
This board will go in anything with the low entry get in early rocker, single to double concave and because you can mix up
the fin set up for the surf du jour.
Two
Constructions
Polyester
– slightly heavier than our EPX II, for those that like the polyester feel.
EPX II - our epoxy
version, is light for high performance surfing, carving, and all around ripping. MOTU FLYER 5.8, 5.10, 6.0, 6.2, 6.8 - 19 3/4 to 21 3/4, 2 3/8 to 3
|
|
Mahana Flyer Model The Mahana Flyer is Chuck's updated performance fish. Low entry
rocker, with a winged swallow, single to double concaves for fitting into tight pockets and a high density wedge stringer
for managed flex all the way off the tail.
One
Construction
EPX
II - our epoxy version, is light for high performance surfing. MAHANA FLYER 5.6, 5.10, 6.2, 6.6 - 19 3/4 to 21 3/4, 2 3/8 to 3
|
|
Pape' Flyer Model
The
Pape' Flyer looks as fun as it rides. Again low entry rocker, with a high winged diamond tail,
single to double concaves make this a master blaster in small to medium surf. This model is a must for every quiver.
Two
Constructions
Polyester – slightly heavier than our
EPX II, for those that like the polyester feel.
EPX II - our epoxy version, is light
for high performance surfing, carving, and all around blasting.
PAPE
FLYER 5.8, 6.0, 6.4 - 20 to 21, 2 3/8 to 2 3/4
|
|
Nui Ma'o Model
The Nui Ma'o (Big Shark) is Chuck's version of the performance funshape. More volume but pulled in nose
and tail for performance.A nice round pin with wings for directional change and a single to double out the tail. Thruster
set up. Two
Constructions Polyester
– slightly heavier than our
EPX II, for those that like the polyester feel.
EPX II - our epoxy version, is light
for high performance surfing, carving, and all around surfing.
NUI MA'O 7.4, 7.6, 7.10 - 21 to 21 3/4, 2 7/8 to
3 |
|
Nui
Poti Model The
Nui Poti (Big Boat) is our performance longboard. Single concave under the nose to flat to slight double out
the tail. Squash tail. Thruster set up. Construction Polyester
– for the classic polyester feel.
NUI POTI 9.0, 9.6 - 22 1/2 to 23, 3 to 3 1/4, S (Nose)/DBL. |
|
|
|
|
